hansgrohe ibox universal installation instructions

Sealing screens, which are included with each hand shower, must not be replaced by normal seals. Sealing screen: What is the purpose of the seal or a sealing screen between the shower hose and the hand shower? Corresponding spare parts numbers for your product are available in the Spare Parts Shop. Square riser pipes are available in different lengths. You will find more information in the relevant installation manual. Shower pipes: Can the riser pipe be shortened?ĭepending on the model, the riser pipes can be adjusted according to the available space and shortened when required. What can I do?īrief dripping after use is physically required on faucets and showers, and does not indicate a product defect which would justify replacement of the fittings or a warranty / guarantee claim. Loosened debris can then be washed away.ĭripping after use: Water always drips from the faucet or shower for a while after use. With the water running, pull the spatula completely through the gush spray outlet. What can be done?Ĭlean the gush spray outlet. Overhead shower: The shower produces an irregular gush spray. You should be able to wash your hair while sitting, without having to hold the hand shower. The hand shower should be within convenient reach. Hand shower: Where should I install the holder on the bath tub? Instructions for correct descaling are shown in this video. What can I do?Ī low flow performance may be caused by a dirty sealing screen. Hand shower: The water flow is very low compared to before. The spacer can also be stacked when needed. In such cases, the plastic tile spacer can then be used. For this reason, it is sometimes necessary to compensate for the thickness of the tiles. Not all bathrooms are tiled to the full room height. Tile spacing: What is the elongated plastic disc that is enclosed with the shower sets used for? Watch this video for the steps involved in installing a corner mounting set. at least in my situation.Wallbar: What options are there for installing it in the corner? this may not be your problem solver but i think/hope this is mine. shut off each one individually to see which side is hot and which side is cold. if you have the 'ibox' rough-in there are 2 service valve shut-offs in there where the supplies come in. in turn, the 'hot' side starts to let in cold water confusing the thermostat to continue calling for hot water but only getting cold. the thermostat starts to call for hot water little by little. then vise-versa when in the 'cold' position rotating towards the 'hot' position. in turn, the 'cold' side starts to let in hot water confusing the thermostat to continue calling for cold water but only getting hot. being a thermostatic valve, when in the 'hot ' position and rotating to the 'cold' the thermostat starts to call for cold water little by little. my plumber crossed my supply lines so that hot is right and cold is left. make sure that the water supplies are connected properly to the rough-in. when rotating back towards the 'hot' position the water does not get hot until almost the 'hot' position and there is no in-between. when rotating towards the 'cold' position the water does not get cold until almost to the 'cold' position. when in the 'hot' position the water is hot. check to see if it is a 'thermostatic' valve in the 'ibox' rough-in. I have the same/similar problem and i've been searching for a solution and with some self-trouble shooting, i found it. I will try to decipher the instructions on turning hot only and cold taps - cold shower and hot taps. I went online - i do not see anywhere on their website manuals or parts ordering to replace any internal mechanisms.

WHen i turn it slowly right - at some point it looks like the 'hot water' side kicks in (the hand shower plumbing line kicks in as if the water is turn on - and then it's scalding HOT.Ĥ. as I slowly turn the knob back clockwise (right) - it 'pops' back in place - but it is still COLD. the knob at the counterclockwise (left rotation) position can 'push in' and rotate another 45 degrees or so.

I can hear what sounds like a spring moving inside the valve - not sure if it's a mechanical failure or not.ģ. I turn it to the far left where it should be cold - it still is scalding hot. I place the valve at the '90 degree' setting - and wait. The dial can turn 180 degrees (cold to hot setting). It is not a problem of 'rushing' the temperature setting. First statement was 'it seems the plumbing is incorrect'.Ģ. THey asked for a picture, but they are off for the holiday. Re: Hansgrohe Temperature Problem (hot and cold)ġ.

Hansgrohe ibox universal installation instructions